undervolting the Turion Ultra

Discussion in 'Hewlett Packard' started by Seketh, Oct 19, 2011.

Thread Status:
Not open for further replies.
  1. arthursantossp

    arthursantossp Pen Pal - Newbie

    Messages:
    50
    Likes Received:
    0
    Trophy Points:
    16
    Thanks 2.0, just tried with CPU-Z.

    I notice other thing, when I set the power plan to high performance, with maximum processor to 100% and minimum processor to 100%, the p0 voltage keeps on 1.013, but the p1 changes to 1.200.

    When I change the minimum processor to 90%, the p0 remais at 1.013 and the p1 drops to 0.775.

    Dont know what is happening (tested with AMD Power Monitor and CPU-Z)...
     
  2. dedraks

    dedraks Pen Pal - Newbie

    Messages:
    26
    Likes Received:
    0
    Trophy Points:
    6
    What about the source code of pumastatectrl?
     
  3. 970261

    970261 Scribbler - Standard Member

    Messages:
    334
    Likes Received:
    0
    Trophy Points:
    31
    did u try PM'ing the creator Mr. Systematic?
     
  4. rino

    rino Pen Pal - Newbie

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    5
  5. dedraks

    dedraks Pen Pal - Newbie

    Messages:
    26
    Likes Received:
    0
    Trophy Points:
    6
    Thank's. :)
     
  6. Bernok

    Bernok Scribbler - Standard Member

    Messages:
    161
    Likes Received:
    0
    Trophy Points:
    31
    When testing a Voltage to decide whether it is stable or not, for how long should I run Prim95's Torture Test?

    I'm sorry if this has been asked. I looked around and I couldn't find the answer.

    Also, I was running Prime95 and I got this error from it:
    Is this because of the voltage? Or do I have to get a BSoD to know that the voltages were too low?
     
  7. ChronoReverse

    ChronoReverse Pen Pal - Newbie

    Messages:
    49
    Likes Received:
    0
    Trophy Points:
    15
    The rounding means it is not stable enough to do math completely correctly. You'll need to increase the voltage a notch.


    As for how long to run it, 30 minutes should be enough to be sure. Make sure your laptop is set in a well-ventilated area to avoid overheating.
     
  8. 64Bit_Chic

    64Bit_Chic Pen Pal - Newbie

    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    5
    i'm using window vista 64 bit and CPU Amd Rm-70...i was running PumaStateCtrlDlgx64 but it didn't work...
     

    Attached Files:

    • 1.JPG
      1.JPG
      File size:
      23.4 KB
      Views:
      166
    • 2.JPG
      2.JPG
      File size:
      23 KB
      Views:
      123
    • 3.JPG
      3.JPG
      File size:
      23.2 KB
      Views:
      116
    • 4.JPG
      4.JPG
      File size:
      24.3 KB
      Views:
      119
    • 5.JPG
      5.JPG
      File size:
      25.1 KB
      Views:
      124
  9. 64Bit_Chic

    64Bit_Chic Pen Pal - Newbie

    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    5
    i'm a newbie :D..Someone help me ...i need a config file for cpu amd Rm-70..Thank everyone...
     

    Attached Files:

    • 6.JPG
      6.JPG
      File size:
      24.7 KB
      Views:
      140
    • 7.JPG
      7.JPG
      File size:
      22.7 KB
      Views:
      132
  10. Bernok

    Bernok Scribbler - Standard Member

    Messages:
    161
    Likes Received:
    0
    Trophy Points:
    31
    change the VID not the values of the voltages. Read the included instructions.

    Someone else's config file won't work for you, all processors are different to a certain extent.
     
Thread Status:
Not open for further replies.

Share This Page